Monday, May 20, 2019

Impression Obsession - Die Cut Obsession

There are so many amazing dies at Impression Obsession - this special Monday feature lets them have the spotlight! We hope you're inspired!

For this project I used a few die sets to dress up a black and white pre-printed card - I used a stencil for the clouds, and then these sets to complete the scene:

Plane with Banner

(It just happens that all the sentiments from my Warm Fuzzies Sentiments and Life Stuff Sentiments sets fit in the banner - those are great sets for every occasion!)

Sun and Moon

Be sure to check out the other designers' blogs for inspiration - see the I.O. blog for all the details!

Thanks for stopping by!

Friday, May 17, 2019

Spellbinders May 2019 Large Die kit

Just checking in with this month's Large Die club kit from Spellbinders! This is a sweet cake builder set that can go in so many different directions. The two main cake pieces have fold-back tabs that allow the cake to pop out from the card with a slight curve. (They're great ticket shapes as well!)

For this card I used a variety of the accessory dies to build a birthday cake - each piece is watercolored using Distress Oxide inks. Each layer piece has a separate inset that creates a beautiful pattern and grid placement for additional embellishments.

Here's an angled photo so you can see the foiling on the words and the metallic watercolor on the candles! The foiling plates are here - such a great multipurpose set.  The stencil I used is from A Colorful Life Designs.

For my second card I used the scalloped inset die to create a border - the die is easy to line up for repeated cutting. I used this stamp, which is one of my newer designs from Impression Obsession.

One last card with the same color palette - for this one I used the smaller cake layer to make a little gift box.

Pro tip - I didn't have any narrow ribbon, so I carefully cut the satin edge off the ribbon I used for the bow! The sentiment I used is here, and this background stamp is one of my favorites!

Here's the full kit, and there's subscription information at the end of my post. Remember to check out the clearance section while you're over at Spellbinders! Lots of great deals in there!

Hope you have a great week! 
Thanks for stopping by!

Ideas, Supplies, Machines, Paper & More

leaf-icon.png Past Club Kits at Member Rates
leaf-icon.png 10% Store Savings
leaf-icon.png Members Only Offers & Deals
leaf-icon.png Earn Creative Rewards for Each Purchase
leaf-icon.png Monthly Inspiration
leaf-icon.png Cancel Anytime
leaf-icon.png Skip Any Month
leaf-icon.png Annual Membership Gift
leaf-icon.png Exclusive Deals 

Wednesday, May 15, 2019

Splitcoast Tutorial: Magic Envelope Card

This week's tutorial over on Splitcoast is a Magic Envelope Card - it's a fun way to use up double sided paper, and it's a card and envelope in one!

I went for a simple belated birthday card - these are new Summer stamps in my collection, and they're just fun! The watercoloring here took just a few seconds - a few random strokes for the background, and a little shading on the image itself. So easy! The sentiment says it all, as sentiments do...

E13792 Birthday Girl
C13791 Birthday Greetings

Here's the card all folded up and ready to mail! I remember loving this type of stationery as a girl - I used to write letters for hours! 

My other stationery project this week has been graduation announcements - my oldest son graduates on Friday! 

Thanks for stopping by!

Ideas, Supplies, Machines, Paper & More

Monday, May 13, 2019

Impression Obsession - Old is New

With such a huge collection of wonderful stamps from so many artists, sometimes the older stamps in the Impression Obsession catalog find their way out of the spotlight. We don't want them to be forgotten, so from now on you'll be seeing our team feature them regularly. We hope you're inspired!

I had this stamp out for a tutorial a couple of weeks ago - this stamp actually is intended for journaling or word art:

L17057 Squiggles

...but I love it for this technique so much! For this card I positioned the stamp in my MISTI and shifted the panel up 1/8" for each new impression.

The little sentiment I used is from this set - it's in the clearance aisle, so if you love it, grab it! Most of the stamps are available in red rubber but you won't find this price again. It's a great travel set, and great for faraway friends.

CL671 Grunge Map = clearance

Be sure to check out the other designers' blogs for inspiration - see the I.O. blog for all the details!
Thanks for stopping by!

Thursday, May 09, 2019

Impression Obsession DT Challenge: Yellow/Blue Color Challenge

The Impression Obsession team's challenge today is to create a project in yellow and blue.

SS-221-G Tennis Shoes
WP915 Fred Said clear set (sentiment)
DIE814 Pinked Stitched Sentiment Banner

I was playing with some different variations of the Spotlight technique for a challenge that's coming up, and this shoe image is a great one for highlighting just certain areas. I stamped both watercolor panels together, and used a variety of watercolors and colored pencils to color a trimmed portion of the top panel. Just a little light stenciling with my favorite stencil ever on the background!

These shoes are part of the Serendipity Stamps collection that's now available at IO! This one has been a long-time favorite in my collection - just so fun.

Be sure to check out the other designers' blogs for inspiration, and remember you can enter these challenges too, using your Impression Obsession stamps! See the I.O. blog for all the details - you might even win a $25 gift certificate!! We'd love to have you join us.
Thanks for stopping by!

Wednesday, May 08, 2019

Splitcoast Tutorial: Graphite Transfer Paper Deboss

This week's tutorial over on Splitcoast is a fun Graphite Transfer Paper Deboss - it's a very simple way to make a background using graphite paper and an embossing folder! Who knew?

These backgrounds are beautiful with added color but I wanted to keep mine simple to show off the tire tracks (I got that folder here but it seems to be retired). The Tin Lizzie die I used is here, and it's pieced together with 3 separate layered cuts. The tires are on the base layer, colored with Copic markers. The other pieces are solid cardstock, shaded with Copics and highlighted with a light grey colored pencil. This is the graphite paper I use.

The stamp is from this set, which is in my line - it's one of my favorite masculine sets, and a great staple set to have!
CL672 Timeless Classic clear set
I hope you're having a great week - I'm recovering from an allergy day and a little giddy that we got Hamilton tickets! My son and I have been saving Christmas and birthday checks for a long time!
Thanks for stopping by!

Ideas, Supplies, Machines, Paper & More

Tuesday, May 07, 2019

Product Review: Crossover II Fabric & Paper Cutting System

I have a new tool in my studio! After researching some different wide format die cutting machines, I was curious about the capabilities of the Crossover II. Most of the reviews I found online were directed more to the quilting market, and it does have lots of great applications for that field (alllll my quilting genes are tingling!), but I wanted to know more about how it would work in our paper crafting world. 

I reached out to the kind people at Crafter's Edge, and they sent me a machine to test out. If you haven't heard of Crafter's Edge, you may have heard of some of their sister brands, like Dies Direct, or Maker's Movement (and if you remember Cheery Lynn Designs, you might recognize some of their dies  at MM too)! You probably already own some dies that have been made in their Arizona facility - Dies Direct is the #1 metal die manufacturer in the USA! 

The Crossover II machine itself is well made, a sturdy plastic outer casing with all-metal gears, rollers and inside construction (this model features some improvements from the earlier Crossover machine - if you've researched this machine you may have seen that model online). 

It is heavy - about 15.6 pounds (that's about 4 pounds heavier than the machine I've been using, just for reference). It does have a large footprint, but folds up nicely for easy and relatively compact storage. Ready for use, the machine sits 17" wide with the handle extended, 6-3/4" high and 21" long. Strong rubber grips keep it from slipping around the workspace.

 Strong velcro dots hold the sides up and together when closed, forming a handle for easy portability. The side handle has a release button that allows it to fold up to tuck into a carrying case or shelf space. In storage mode, it's 9" high, 4-1/2" thick, and 14" wide.

The machine comes with 3 plates. The thicker base plate is 8-1/2" x 12-1/4" and provides a sturdy platform for most cuts. The short ends are beveled for easy carriage through the rollers. The top clear plate is slightly smaller, 8-1/2" x 12". This plate holds the dies in place and can also be used as a cutting plate for paper cutting dies. There is a metal plate that is 8" x 10" - it functions as a shim and provides stability and a firm surface for heavier or more detailed cutting. 

Since I'm accustomed to an upper and lower cutting plate, I was curious if the plates from my other wide format machine would fit, and they do not - they're about 3/8" wider than the Crossover plates. (The Crossover plates will fit into other machines width-wise - but sandwiches and shims would have to be adjusted for cutting purposes because the plates together create a different thickness.) I was also curious if my 6" magnetic base and cutting plates would fit through the rollers, and they do, with the rollers fully open.

The most interesting and unique feature of this machine is a dial on the top panel that moves the top roller up and down. Shown fully open here, you can see a gap on the outside wall between the rollers on the right. That space represents the difference between the rollers fully open and in their lowest position. It's about 3/16" - 1/4" difference. 

Though that seems like a small distance, this function allows precise control in cutting materials of different thicknesses, from paper to 6mm foam sheets, blanket fabric and leather, and allows the machine to adjust for steel rule dies and for other functions, such as embossing with stencils and folders. 

The adjustable rollers also accept all kinds of dies: the familiar wafer thin steel dies, the steel rule dies with a heavier plastic or wood base, as well as the Crafter's Edge Fab Dies (in teal above) and Maker's Movement Versa Dies (more about those soon - they cut shaker frames and other foam pieces to make projects pop!). These unique dies look similar to wafer thin dies, but have deeper cutting lines. This allows them to cut through up to 8 layers of fabric at once (ideal for quilters) and thicker materials that standard wafer dies can't handle, such as matboard, leather, copper sheeting, and balsa wood.

The Crossover II comes with an informative manual, which includes a chart of media and suggested dial settings - this was really helpful as I experimented with different materials, thicknesses, and techniques. I added my own notes as I went along, and quickly got a feel for appropriate settings as I worked. I'm planning to make a swatch book with samples and numbers so I can have a quick reference guide posted near my machine as I work.

The chart covers everything from cotton to leather for the Fab Dies, along with types of paper and settings for the wafer dies, settings for embossing, and settings for steel rule dies. It's recommended to make a test cut when starting off with a new material, and I found it best to start at a larger number and work down. If you're accustomed to a machine with stationary rollers, it is easy to tell when the pressure is too high as the rollers will not feed. The rollers should not be adjusted when the plates are between them, so I'd simply roll back and open the rollers a little wider, and try again. The rollers aren't locked into whole-number settings - for some materials I found an in-between setting worked best. Cardstock and watercolor paper cut well with wafer dies at 5.5, for example.

I had done a little shopping for cuttable materials over the weekend, so I had a wide selection of things to cut! Using a small circle Fab Die (a piece from the set that comes with the machine) I was able to cut through watercolor paper, canvas, glittered fabric sheets, matboard, corrugated cardboard, 6mm foam sheets, copper, leather, faux fur, backed burlap, magnet sheet, and wool felt. 

Paper cutting dies performed beautifully. I tried some dies that had been problematic in my other machines and they were still problematic, to be honest. Some dies just require a few more runs and rotations.These dies though - perfect, clear cuts and details, and that dot border just fell out.

ETA: I reran my most frustrating die at a higher pressure and it cut perfectly. I'm in love, officially.

Embossing folders worked easily with no need for special shims or configurations. I like the fact that I can adjust the pressure for a deeply embossed pattern or more subtle effect.

Dies can be debossed easily, again with no need for shimming. My initial tests were done with too much pressure and the paper cracked in the open areas of the die. Once I found the right setting, the results were perfect. 

Stencils and texture plates also embossed beautifully. For these types of debossing techniques, a silicon pad is needed as a cushion... Note: Crafter's Edge does not carry these, so one would need to be purchased separately. 

If you have a foiling machine that requires a die cutting machine to press and set the foil, the Crossover is easily adjusted to the thickness of the heated platform.

My thoughts:

--I've been really pleased with the Crossover II machine overall! I love that I can accomplish all the things I've listed above on a single machine and platform - some of these functions were requiring multiple shims and sandwich adjustments, or even switching platforms or machines. Shimming always seems like a waste of materials, so it's nice to be able to save those sheets of chipboard or cardstock for true creative work.

--I'm thrilled with the variety of materials that I can cut. The deeper Fab Dies open up so many possibilities, I'm not even sure where to begin! Quilt squares, applique, ornaments and tags... I'm excited that they can cut out matboard, since that is the surface I love to use for mixed media and colored pencil - imagine original hand-colored or painted pendants or earrings! How fun would those be?! 

A few things to consider:

--The machine does have a large footprint, and with its weight, it's best suited for a dedicated space. If you're working in a tight area or don't have a dedicated space for a larger machine, that may be an issue for you. 

--To view the dial, you do need to have the handle on the right side of the machine. I'm left-handed, and I usually crank with my left hand, but it turns out that I haven't had trouble with the right-handed orientation. The handle turns very easily, and doesn't have a pin that will loosen over time, an issue I've experienced with other machines (maybe because of the left-handed turning...?). 

--I had a little trouble with the positioning of the velcro dots, but I fixed it! The 'hook' side of the velcro is placed on the user side of the machine, and it was a little scratchy and kept catching on my sweater sleeve. I found it removed easily, so I switched the soft side to the front. Problem solved. 

--The price. The MSRP of the machine is $249.99. Considering all the directions this machine can take us as designers though, it seems like a worthy investment, especially if you enjoy multimedia work. I’m excited about the possibilities. I do know that Crafter's Edge and their sister sites offer occasional discounts, so look out for those - you may want to sign up for their newsletters or follow their social media sites so you don't miss out! Amazon has the machine at a small discount with free shipping, and it's available through other retailers as well, including QVC!

I hope this review has been helpful, and I’ve been able to communicate all the things that the Crossover II can do! If you have any questions please let me know and I'll do my best to test out or search out the answers for you!

Thanks for stopping by!

Ideas, Supplies, Machines, Paper & More